Invotel SX1025 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Audio Invotel SX1025. Invotel SX1025 User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 2
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
Music-On-Hold Adapter Installation
AudioImage
Model # SX1025
Rev 22X
Connect “WALL jack” to your “Wall” Jacks using the provided cord .
This device monitors all the telephones through the lines. You may use a splitter
(T adapter) at the Wall jack to connect both this device and a telephone. If you
do not have a splitter use the “PHONE” jack on this device to plug the
telephone.
Please note that just one phone may be optionally connected to this
device, other telephones remain connected to their own wall jacks.
Plug the Audio cable into Audio IN jack on the AudioImage™ Music On Hold
controller, Plug the other end of audio cable into the “Headphone” jack of your
audio source such as digital player (8 ohm or 600 ohm), Radio, CD Player, PC
CD ROM headphone, PC sound card, speakers output etc.
We recommend you to set the volume on your audio source to mid level
Note: extensive volume can shut off the on-hold audio.
(please note some music titles are not royalty-free and you may want to use the royalty-
free music titles to avoid annual licensing payments to ASCAP and BMI for playing those
titles on-hold)
L1 Out Audio L1 IN
Wall
jack
Phone
Unplug the phone lines; Wait 60 seconds then Plug them back IN.
make sure the phone line is plugged in securely.
Select Line 1 on the phone & make sure that there is dial tone.
2. No Audio
check audio cord; try inserting it half way, adjust the volume on your
audio source if needed to hear it.
3. Audio source is OK but no
audio when device is
activated.
Verify that the audio source is playing by itself, listen to it. Use the
Headphone jack on a CD player not the “line out”
Set Volume to Medium.
If answering a call allow a second before placing the call on HOLD.
Check to see if LED light on this device has turned ON
model SX1025 does not activate by pressing Hold button
you need to press Flash button 1
st
then Hold button. On some
phones wait a second after pressing Flash then press Hold.
4.
MOH works but audio does
not stop when call is picked
up in any setting
You need to press FLASH button to stop the audio
Wire distance to adapter may be too long(more than 200 feet),
Centralize the location of device to be as close as possible to the
phones.
5.
Some Phones work , some
do not
Make sure all phones are compatible between each other
6.
Some times audio starts to
play by it self or does not
deactivate.
Press FLASH button to stop it.
The call needs to be on Hold at least 4 seconds before use Flash to
deactivate.
When you hang up, wait 2 seconds before selecting the same line.
Check for other devices sharing that line like Message indicator,
Answering machine, Alarm system, Modem etc. Use a privacy
module between the line and that device to keep them off the line
when line is being used by your phone.
Set your Alarm system and/or your DSL line to share FAX line.
Excessive wiring- Total wire length per line must be under 200 feet.
1.
Adapter not working or
stopped working
Problems Possible Cause / Solution
7.
Audio shuts off or flickers
Extensive audio volume, adjust the volume to proper level.
If you are using a PC for audio source you may need an “audio
ground loop isolator” Radio shack part# 2700054
P4
Innovative Telecommunication Technology
1112 Montana Ave Suite 250 Santa Monica, CA 90403 USA
Toll-Free: 800-747-0708 Tel: 310-899-0078 Fax: 310-899-0227 http://www.invotel.com
®
Vue de la page 0
1 2

Résumé du contenu

Page 1 - Model # SX1025

Music-On-Hold Adapter InstallationAudioImage™Model # SX1025 Rev 22X• Connect “WALL jack” to your “Wall” Jacks using the provided cord . • • • •

Page 2 - Operation:

iiIMPORTANT NOTE: The audio may activate in the middle of a call due tofactors like excessive wiring (see page 4 item 8), bad or old wiring , existing

Modèles reliés SX2010 | SX4020 |

Commentaires sur ces manuels

Pas de commentaire